Charpy and Izod Method Impak  Strength Analysis on ST 37 Steel with Temperature Variations

Eka Putra Dairi Boangmanalu; Angga Bahri Pratama; Al Qadry; Jandri Fan HT Saragi; Franklin Taruyun Hudeardo Sinaga

doi:10.55927/fjst.v2i12.7074

Authors

Eka Putra Dairi Boangmanalu Jurusan Teknik Mesin Politeknik Negeri Medan
Angga Bahri Pratama Jurusan Teknik Mesin Politeknik Negeri Medan
Al Qadry Jurusan Teknik Mesin Politeknik Negeri Medan
Jandri Fan HT Saragi Jurusan Teknik Mesin Politeknik Negeri Medan
Franklin Taruyun Hudeardo Sinaga Jurusan Teknik Mesin Politeknik Negeri Medan

DOI:

https://doi.org/10.55927/fjst.v2i12.7074

Keywords:

Impak, Charpy, Izod, Temperature

Abstract

This research is impact testing using the Charpy and Izod methods, temperature variations of 1500 C, 2500 C and raw material as the research variable. The results of the Charpy test with a variation of 150 0C obtained a maximum absorbed energy of 97.65 J, with an impact value of 0.222 J/mm2. Then the maximum energy absorbed through testing at a temperature of 2500C is 78.28 Joules and the impact value is 0.177 J/mm2. Furthermore, the raw material test results showed that the maximum energy absorbed was 145.96 J with an impact value of 0.330 J/mm2. Izod testing with a temperature of 1500C obtained a maximum absorbed energy of 60.94 J with an impact value of 0.101 J/mm2. Furthermore, the maximum energy absorbed at a temperature of 2500C is 36.83 Joules and the impact value is 0.061 J/mm2. The raw material test results show that the maximum energy that can be absorbed is 80.53 J with an impact price of 0.133 J/mm2

Downloads

Download data is not yet available.

References

Dan, I., Pada, T., Baja, C., Suhada, K., & Yanhar, M. R. (2023). ANALISA KEMAMPUAN PENGELASAN TERHADAP BEBAN. 162–171.

Fan, J., Saragi, H. T., Pratama, A. B., Putra, E., Boangmanalu, D., & Qadry, A. (2023). Pengaruh Temperatur terhadap Kekuatan Impak pada Material Besi Nako 10 mm. 04(01).

Majanasastra, R. B. S. (2011). KARBON TINGGI ( AISI D2 ) HASIL PERLAKUAN PANAS. Aisi 1045.

Nasution, M., & Nasution, R. H. (2020). TERHADAP PERLAKUAN CARBURIZING DENGAN ARANG BATOK KELAPA. 15(2).

Nuhgraha, Y., Rosa, M. K. A., & Agustian, I. (2020). Perancangan Alat Uji Impak Digital dengan Metode Charpy Untuk Mengukur Kekuatan Material Polimer. 10(2), 15–19.

Pratama, A. B., Studi, P., Mesin, T., Andalas, U. D., Studi, P., Mesin, T., & Andalas, U. D. (2021). Analisis tegangan alat uji bending pipa skala laboratorium menggunakan finite element analysis. 3(1), 201–205.

Widiyarta, I. M., & Sucipta, M. (2018). Kekerasan Baja Karbon Sedang dengan Variasi Suhu Permukaan Material. 4(2), 43–48.