Comparative Analysis of Reinforcement Efficiency in Beams and Columns for the North Minahasa-North Sulawesi Civil Servants Flats Project

Hendrie Palar; Don  Kabo; Herman Tumengkol

doi:10.55927/fjsr.v3i4.8928

Authors

Hendrie Palar Manado State Polytechnic
Don Kabo Manado State Polytechnic
Herman Tumengkol Manado State Polytechnic

DOI:

https://doi.org/10.55927/fjsr.v3i4.8928

Keywords:

ETABS, Economical Reinforcement, Columns and Beams

Abstract

This study aims to (1) compare the reinforcement from the calculation of beams and columns with the reinforcement installed in the North Minahasa Civil servantsFlats Project, (2) to analyze whether the reinforcement installed in the North Minahasa Civil servantsFlats Project is economical or not. This research was conducted in the Department of Engineering at the Manado State Polytechnic. The method used in this research is quantitative with the method of observation. The material and structural data used are the same as those in the project. The results of this study were carried out with the help of the Etabsv20 program. Based on the results of the reinforcement calculations that have been carried out, the comparison of the area of reinforcement (AS) for columns and beams between the results of ETABS and the results of the area of reinforcement installed in the project is obtained which is then converted in percentage form. In the beam, the largest percentage ratio is in the upper support area by 60% and in the plane located in the lower plane by 60%. While in the comparison column the percentage of reinforcement column (AS) from the project with the largest ETABS result is 40%

Downloads

Download data is not yet available.

References

Anggraini, S., Septiandini, E., & Wangi, I. P. (2024). Jurnal Talenta Sipil. Talenta Sipil, 7(1), 238–246. https://doi.org/10.33087/talentasipil.v7i1.437

Hutabarat, A., Praditya, A. B., Tudjono, S., Nurhuda, I., Sipil, J. T., Teknik, F., Diponegoro, U., Induk, B., Struktur, P., & Gempa, T. (2015). Perencanaan struktur gedung kuliah utama fakultas teknik universitas diponegoro semarang. 3, 48–55.

Liando, F. J. (2020). PERENCANAAN STRUKTUR BETON BERTULANG GEDUNG KULIAH 5 LANTAI. 8(4), 471–482.

Nabilah, D., & Zev Aljauhari. (2022). PERENCANAAN ULANG STRUKTUR KOLOM GEDUNG RUSUNAWA SATBRIMOB POLDA KEPRI BATAM. Seminar Nasional Industri Dan Teknologi (SNIT), Politeknik Negeri Bengkalis, 2019(November), 670–678.

Rusalim, A., Ermiyati, Azhari, Novan, A., & Morena, Y. (2024). Analisis struktur balok pada proyek gedung kampus stie dan stikom yayasan pelita indonesia kota pekanbaru-riau. Journal of Civil Engineering, Building and Transportation, 8(1), 27–37. http://ojs.uma.ac.id/index.php/jcebt

Standardization Agency. (2019). SNI-1726-2019 Planning Procedures Resilience Earthquake For Structure Buildings and Non-buildings. Jakarta: National Standardization Agency.

Standardization Agency. (2019). SNI-2847-2019 Requirements Concrete Structural For Buildings and Explanations. Jakarta: National Standardization Agency .

Standardization Agency. (2020). SNI-1727-2020 Minimum Design Load and Criteria related For Buildings and Other Structures. Jakarta: National Standardization Agency.